PSI LCENTLT2 No. 2MT Heavy Duty Live Tailstock Center

Ball bearing precision; turns smoothly. Ideal to support your work at the tailstock end of your lathe. 60-degree point. Huge live center for heavy duty workpieces. Heavy duty #2mt live tailstock center with a 60 degree point. Huge live center for heavy duty workpieces. Cone is 2-1/2" long, by 1-11/16" diameter. Cone is 2-1/2" by 1-11/16" overall diameter.

It runs very true and is also well balanced and smooth for effective turning. This center is large and strong with precision bearings. Large live lathe center.

---

PSI Woodworking Products TM32 1/2-Inch Diameter Drill Chuck with a 2 MT Mount

Drill chuck mounts in the 2 MT. Accepts a 1/4-20" draw bolt not supplied for safety. Will hold drill bits up to 1/2-Inch in diameter. Can be used in either the headstock or tailstock. Will hold drill bits up to 1/2-Inch in diameter. Removed easily with a knock-out bar. Removed easily with a knock-out bar. 2 morse taper mount for delta, PSI, Jet, and other Midi lathe headstocks and tailstocks.

Drill chuck mounted in the #2 MT can be used in either the headstock or tailstock. A 1/2-inch diameter 3-jaw mechanism can be used for securing small turnings or pen mandrels at the headstock, or a drill bit in the tailstock. Tightens with a chuck key for excellent grip. Tightens with a chuck keyincluded for excellent grip.

.


Similar products

---

PSI Woodworking LCENTSS22 No. 2 MT with 1-Inch Crown Super Wood Lathe Drive Center

There is no need to hammer your drive center into the work piece and risk splitting your work. The psi super center Crown compatible with headstocks with #2MT spindles. Spring loaded point simplifies spindle centering and retracts to avoid spitting your work when tailstock pressure is applied. Will hold drill bits up to 1/2-Inch in diameter.

More teeth give a better bite while providing equal pressure and a positive drive. The psi super center Crown compatible with headstocks with #2MT spindles. Ships in plastic production sleeves at 4. 8-ounces. Can be used in either the headstock or tailstock. Get a better bite on your spindle with more teeth for a strong grip while still providing equal pressure and a positive drive.

4. 5" by 1. 5" by 1. 5" with a 1-inch crown. Get a better bite on your spindle with PSI's new 1' Super Center. Tightens with a chuck key for excellent grip. 4.


Similar products

---

Robert Larson 800-2875 Plastic Center Finder

Place on your wood stock to quickly find the center. Get a better bite on your spindle with more teeth for a strong grip while still providing equal pressure and a positive drive. 4. 5-by-1. 5-by-1. 5-inches with 1-inch crown. Round stock capacity 8". Hexagon stock capacity 5 3/4". Square capacity 8". Drill chuck mounts in the 2 MT.

Handy for all woodworkers. Tightens with a chuck key for excellent grip. Ships in plastic production sleeves at 4. 8-ounces. Will hold drill bits up to 1/2-Inch in diameter. A simple yet effective tool. Removed easily with a knock-out bar. Octagon stock capacity 8". Can be used in either the headstock or tailstock. The psi super center Crown compatible with headstocks with #2MT spindles.

Spring loaded point simplifies spindle centering and retracts to avoid spitting your work when tailstock pressure is applied.


Similar products

---

PSI Woodworking Products CF3J Faceplate 1-Inch by 8TPI 3-Inch Diameter

Octagon stock capacity 8". Removed easily with a knock-out bar. Get a better bite on your spindle with more teeth for a strong grip while still providing equal pressure and a positive drive. Tightens with a chuck key for excellent grip. Perfect for all small bowl turning. Spring loaded point simplifies spindle centering and retracts to avoid spitting your work when tailstock pressure is applied.

Round stock capacity 8". All steel construction. Drill chuck mounts in the 2 MT. Has machined flats to grip with a wrench - easy on and easy off. Ships in plastic production sleeves at 4. 8-ounces. 4. 5-by-1. 5-by-1. 5-inches with 1-inch crown. Fits any lathe with a 1-Inch by 8TPI spindle thread. 3-inch diameter faceplate with 4 screw mounting holes.

This 3-inch diameter faceplate has 4 screw mounting holes, and two machined flats to grip with a wrench - easy on and easy off. Fits any lathe with a 1" x 8 tpi spindle thread.


Similar products

---

Einstein Tool Co. 1/2" JT33 Drill Chuck 2 MT Arbor/Mount for Lathes and Drill Presses Two Keys

Has machined flats to grip with a wrench - easy on and easy off. Fits any lathe with a 1-Inch by 8TPI spindle thread. Chuck overview Customer satisfaction is our number one priority. Handy for all woodworkers. 4. 5-by-1. 5-by-1. 5-inches with 1-inch crown. 3-inch diameter faceplate with 4 screw mounting holes. Round stock capacity 8".

Threaded 7/16-18. Octagon stock capacity 8". This chuck works with most drill presses and lathes. Chuck specifications: brand new capacity 1/32" to 1/2" chuck input taper is jt33 - jacobs taper 33 compatible arbor is jt33 on the chuck side and MT2 - Morse taper #2 compatible on the Lathe / Drill press side Arbor is tapped for use with draw bars 7/16-20 Knurled body offers superior grip over standard chucks Two chuck keys included Will hold drill bits up to 1/2-Inch in diameter.

Do not hesitate to reach out with questions or requests. This is the best drill chuck for the money to use with lathes and drill presses. Hexagon stock capacity 5 3/4". Get a better bite on your spindle with more teeth for a strong grip while still providing equal pressure and a positive drive. 2mt taper fits most drill presses and lathes.

All steel construction.


Similar products

---

PSI Woodworking LCTEN HSS Wood Lathe Tenon Tool

Removed easily with a knock-out bar. A must tool for any pen maker. Get a better bite on your spindle with more teeth for a strong grip while still providing equal pressure and a positive drive. Can be used in either the headstock or tailstock. A must tool for any pen maker for cutting perfect tenons on pen center bands.

Drill chuck mounts in the 2 MT. Round stock capacity 8". Handy for all woodworkers. Fits any lathe with a 1-Inch by 8TPI spindle thread. For cutting perfect tenons on pen center bands. Get a clean, sharp and accurate 90 degree angle corner for delicate turnings. Threaded 7/16-18. Hexagon stock capacity 5 3/4". Capacity 1/32" to 1/2".

The psi super center Crown compatible with headstocks with #2MT spindles. Ships in plastic production sleeves at 4. 8-ounces. Has machined flats to grip with a wrench - easy on and easy off. 2mt taper fits most drill presses and lathes.


Similar products

---

Big Horn 19053C 3 Pieces 8-Inch Spring Caliper / Divider Set

Has machined flats to grip with a wrench - easy on and easy off. Precision ground with threaded spool mechanism for infinite adjustment. Can be used in either the headstock or tailstock. 4. 5-by-1. 5-by-1. 5-inches with 1-inch crown. Get a clean, sharp and accurate 90 degree angle corner for delicate turnings. A must tool for any pen maker.

All steel construction. Capacity 1/32" to 1/2". Will hold drill bits up to 1/2-Inch in diameter. Threaded 7/16-18. Big horn inside calipers are great for gauging the inner diameter of an opening and then transferring that measurement to a ruler. Measures 1/16 inches wide. Removed easily with a knock-out bar. Perfect for all small bowl turning.

Round stock capacity 8". Drill chuck mounts in the 2 MT. Spring loaded point simplifies spindle centering and retracts to avoid spitting your work when tailstock pressure is applied. The psi super center Crown compatible with headstocks with #2MT spindles. Ships in plastic production sleeves at 4.


Similar products

---

NOVA 48232 G3 Reversible Wood Turning Chuck Dedicated to fit 1" x 8tpi lathe spindles only

4. 5-by-1. 5-by-1. 5-inches with 1-inch crown. Big horn inside calipers are great for gauging the inner diameter of an opening and then transferring that measurement to a ruler. Accepts full range of NOVA Chuck Accessories. Awarded best value in Chuck Test by Wood Magazine Sept 2011. 3-inch diameter faceplate with 4 screw mounting holes.

Fits any lathe with a 1-Inch by 8TPI spindle thread. Square capacity 8". Ships in plastic production sleeves at 4. 8-ounces. A must tool for any pen maker. Dedicated to fit 1" x 8tpi lathe spindles. It comes with a reverse lock feature that enables the chuck to be locked securely onto the lathe spindle when using the forward and reverse functions on the NOVA 46000 Comet II Lathe.

Anti-release spindle lock, ensures chuck will stay securely mounted on the NOVA 46000 Comet II Midi Lathe during forward and reverse turning. The psi super center Crown compatible with headstocks with #2MT spindles. Designed by the innovators of the 4 Jaw Chuck for wood turning, Teknatool International - since 1955.

Get a better bite on your spindle with more teeth for a strong grip while still providing equal pressure and a positive drive. Get a clean, sharp and accurate 90 degree angle corner for delicate turnings.


Similar products

---

PSI Woodworking PKMS2SET Pen Mandrel Saver Package #2MT,

The psi super center Crown compatible with headstocks with #2MT spindles. Your bushings press against the center with Zero pressure on the Mandrel shaft. For cutting perfect tenons on pen center bands. Threaded 7/16-18. Fits any lathe with a 1-Inch by 8TPI spindle thread. 4. 5-by-1. 5-by-1. 5-inches with 1-inch crown.

Open back for easy cleaning. High powered Tuff Lock gearing delivers outstanding grip for little effort. Can be used in either the headstock or tailstock. Perfect for metal and wood lathes. Lifetime Warranty. Big horn inside calipers are great for gauging the inner diameter of an opening and then transferring that measurement to a ruler.

Hardened and tempered bow springs and fulcrum spools assure uniform tension without side play while using this caliper set. Mandrels usually bend when you tighten the Tailstock center point into the end indentation of your Mandrel. Will hold drill bits up to 1/2-Inch in diameter. Accepts full range of NOVA Chuck Accessories.

Get a clean, sharp and accurate 90 degree angle corner for delicate turnings.


Similar products

---

Hold Fast Non-Stick Bushings for CA Pen Finishing Original Version

Ships in plastic production sleeves at 4. 8-ounces. Tightens with a chuck key for excellent grip. Includes two keys for those times a key walks off on you. Hss wood lathe tenon tool. Square capacity 8". Fast comfortable T Bar handle. Big horn flat leg dividers is a useful measurement transfer tool for uneven surfaces; Also great for a variety of uses such as tracing contours and scribing circles into metal.

Big horn inside calipers are great for gauging the inner diameter of an opening and then transferring that measurement to a ruler. No more bushings glued to barrels. Accepts full range of NOVA Chuck Accessories. Tmi has created 60° hold fast cone bushings made from a nonstick material that will allow you to apply a CA finish safely and easily without adhering the pen bushings to the pen barrels.

No more glued together barrels and bushings. 4. 5-by-1. 5-by-1. 5-inches with 1-inch crown. For cutting perfect tenons on pen center bands. No more bushings glued to your newly turned pen.


Similar products